| Code | Parameter / Meaning | Display Values / adjustable value or explanations | Factory setting | Own setting | Article Page / Links |
|---|---|---|---|---|---|
| D.000 | Heating partial load | Adjustable partial heat load in kW Auto: Product automatically adjusts max. partial load to current system demand |
Auto | ||
| D.001 | Pump overrun: Heating | 1 to 60 min | 5 min | ||
| D.002 | Max. anti-cycl. time: Heating | 2 to 60 min | 20 min | ||
| D.003 | Outlet temperature actual value | In °C | Not ad- justable | ||
| D.004 | Cylinder temperature actual value | In °C | Not ad- justable | ||
| D.005 | Heating target flow temperature | In °C; the maximum value that is set in D.071 and is restricted by means of an eBUS control if such a control is connected | Not ad- justable | ||
| D.006 | Outlet temperature target value | 35 to 65 °C | Not ad- justable | ||
| D.007 | Comfort mode target value APC target value Cylinder temperature target value |
Product with integrated domestic hot water generation, and product with integrated domestic hot water genera- tion and shift-load cylinder 35 to 65 °C Product with heating mode only Frost protection is at 15 °C, then 40 to 70 °C (max. temperature can be adjusted under D.020) |
Not ad- justable | ||
| D.008 | Controller 3-4 | Room thermostat open (no heat requirement) Room thermostat closed (heat requirement) | Not ad- justable | ||
| D.009 | eBUS controller target value | n °C | Not ad- justable | ||
| D.010 | Internal pump | On, Off | Not ad- justable | ||
| D.011 | External pump | On, Off | Not ad- justable | ||
| D.012 | Cyl. charging pump | On, Off | Not ad- justable | ||
| D.013 | Circulation pump | On, Off | Not ad- justable | ||
| D.014 | Pump speed target value | Target value of internal high-efficiency pump in %. Pos- sible settings: 0 = Auto 1 = 53 2 = 60 3 = 70 4 = 85 5 = 100 |
0 = Auto | ||
| D.015 | Pump speed actual value | Actual value for internal high-efficiency pump in % | Not ad- justable | ||
| D.016 | Controller 24 V DC: Heating mode | Heating mode off/on | Not ad- justable | ||
| D.017 | Control type | Control type: 0 = Flow, 1 = Return Return: Automatic detection function for heat output inactive. Max. possible partial heat load when D.000 is on Auto. |
|||
| D.018 | Pump operating mode | 1 = Comfort (continuously operating pump) Internal pump is switched on when the heating flow tem- perature is not at Heating off and the heat requirement is enabled via an external control 3 = Eco (intermittently operating pump) Internal pump is switched on every 25 minutes for 5 minutes once the overrun time has elapsed |
3 = Eco | ||
| D.019 | Pump operating mode: 2-stage pump | Setting for two-stage pump operating mode 0: Burner mode stage 2, pump prerun/overrun stage 1 1: Heating mode and pump prerun/overrun stage 1, domestic hot water mode stage 2 2: Automatic heating mode, pump prerun/overrun stage 1, domestic hot water mode stage 2 3: Always stage 2 4: Automatic heating mode, pump prerun/overrun stage 1, domestic hot water mode stage 1 |
2 | ||
| D.020 | Max. DHW temperature target value | Adjustment range: 50–70 °C (actoSTOR 65 °C) | 65 °C | ||
| D.022 | DHW demand | On, Off | Not ad- justable | ||
| D.023 | Heating mode status | Heating on, heating off (summer mode) | Not ad- justable | ||
| D.025 | Ext. eBUS signal: Cylinder char- ging | On, Off | Not ad- justable | ||
| D.026 | Auxiliary relay | 1 = Circulation pump 2 = External pump 3 = Cylinder charging pump 4 = Extraction hood 5 = External solenoid valve 6 = External fault message 7 = Solar pump (not active) 8 = eBUS remote control (not active) 9 = Anti-legionella pump (not active) 10 = Solar valve (not active) |
2 = External pump | ||
| D.027 | Accessory relay 1 | Switching of relay 1 on the VR 40 "2 in 7" multi-func- tional module 1 = Circulation pump 2 = External pump 3 = Cylinder charging pump 4 = Extraction hood 5 = External solenoid valve 6 = External fault message 7 = Solar pump (not active) 8 = eBUS remote control (not active) 9 = Anti-legionella pump (not active) 10 = Solar valve (not active) |
2 = External pump | ||
| D.028 | Accessory relay 2 | Switching of relay 2 on the VR 40 "2 in 7" multi-func- tional module 1 = Circulation pump 2 = External pump 3 = Cylinder charging pump 4 = Extraction hood 5 = External solenoid valve 6 = External fault message 7 = Solar pump (not active) 8 = eBUS remote control (not active) 9 = Anti-legionella pump (not active) 10 = Solar valve (not active) |
2 = External pump | ||
| D.029 | Water circulation vol. actual value | Actual value in m3/h | Not ad- justable | ||
| D.033 | Fan speed target value | In rpm | Not ad- justable | ||
| D.034 | Fan speed actual value | In rpm | Not ad- justable | ||
| D.035 | 3-way valve position | Heating mode Parallel operation (mid-position) DHW mode |
Not ad- justable | ||
| D.036 | DHW flow rate | In l/min | Not ad- justable | ||
| D.039 | Solar inlet temp. actual value | Actual value in °C | Not ad- justable | ||
| D.040 | Flow temperature actual value | Actual value in °C | Not ad- justable | ||
| D.041 | Return temperature actual value | Actual value in °C | Not ad- justable | ||
| D.044 | Ionisation value actual value | Display field 0 to 1020 > 800 no flame < 400 good flame |
Not ad- justable | ||
| D.046 | Pump mode | 0 = Relay with disable facility 1 = PWM with disable facility | 0 = Relay with disable facility | ||
| D.047 | Current outside temperature | (with Vaillant weather-compensated control) Actual value in °C | Not ad- justable | ||
| D.050 | Offset min. speed | In rpm, adjustment range: 0 to 3000 | Nominal value set in factory | ||
| D.051 | Offset max. speed | In rpm, adjustment range: -990 to 0 | Nominal value set in factory | ||
| D.058 | Solar post-heating | 0 = Solar post-heating deactivated 3 = DHW activation target value minimum 60 °C, thermo- static mixing valve required between product and draw- off point |
0 = Solar post-heating deactivated | ||
| D.060 | Number of safety therm. shut- downs | Number of shutdowns | Not ad- justable | ||
| D.061 | No. of shut-downs in ign. flame controller | Number of unsuccessful ignitions in the last attempt | Not ad- justable | ||
| D.064 | Avg. ignition time | In seconds | Not ad- justable | ||
| D.065 | Max. ignition time | In seconds | Not ad- justable | ||
| D.067 | Remaining anti-cycl. time for heat- ing | In minutes | Not ad- justable | ||
| D.068 | Number of first start attempts | Number of unsuccessful ignitions | Not ad- justable | ||
| D.069 | Number of second start attempts | Number of unsuccessful ignitions | Not ad- justable | ||
| D.070 | 3-way valve operation | 0 = Normal operating mode 1 = Parallel operation (mid-position) 2 = Permanent heating position |
0 = Normal operating mode | ||
| D.071 | Max. heating target flow temp. | 40 to 80 °C | 75 °C | ||
| D.072 | Pump overrun after cylinder char- ging | Adjustable from 0–10 minutes in increments of 1 minute | 2 mins | ||
| D.073 | Offset setting for comfort mode | Adjustable from-15Kto5K | 0 | ||
| D.074 | Anti-legionella funct. with integ- rated cyl. | 0 = Off 1 = On |
1 = On | ||
| D.075 | Max. cylinder charging time | 20–90 min | 45 mins | ||
| D.076 | Device Specific Number | Device specific number = DSN 1 = VU 126/5-5 (H-GB) ecoTEC plus 612 3 = VU 156/5-5 (H-GB) ecoTEC plus 615 4 = VU 186/5-5 (H-GB) ecoTEC plus 618, VU 186/5-5 (P-GB) ecoTEC plus 618 9 = VU 246/5-5 (H-GB) ecoTEC plus 624 14 = VU 306/5-5 (H-GB) ecoTEC plus 630, VU 306/5-5 (P-GB) ecoTEC plus 630 20 = VU 386/5-5 (H-GB) ecoTEC plus 637 6 = VUW 196/5-5 (H-GB) ecoTEC plus 825 10 = VUW 246/5-5 (H-GB) ecoTEC plus 832, VUW 246/5-5 (P-GB) ecoTEC plus 832 62 = VUW 306/5-5 (H-GB) ecoTEC plus 835 17 = VUW 286/5-5 (H-GB) ecoTEC plus 838, VUI 286/5- 5 (H-GB) ecoTEC plus 938 |
Not ad- justable | ||
| D.077 | DHW partial load | Adjustable cylinder charging output in kW | |||
| D.078 | DHW max. flow temperature | Limit on cylinder charging temperature in °C 50 °C – 80 °C Note The chosen value must be at least 15 K or 15 °C above the target cylinder value. |
75 °C | ||
| D.080 | Heating operating hours | In hours (h) | Not ad- justable | ||
| D.081 | DHW operating hours | In hours (h) | Not ad- justable | ||
| D.082 | Heating burner starts | Number of burner start-ups | Not ad- justable | ||
| D.083 | DHW burner starts | Number of burner start-ups | Not ad- justable | ||
| D.084 | Maintenance in | Adjustment range: 0 to 3000 hrs and "—" for deactivated | „—” | ||
| D.088 | Min. DHW flow rate | Switch-on delay for domestic hot water draw-off detec- tion via impeller (only products with integrated domestic hot water generation) 0 = 1.5 l/min and no delay, 1 = 3.7 l/min and 2 sec. delay |
1.5 l/min and no delay | ||
| D.090 | eBUS controller | Status of digital control Recognised, not recognised | Not ad- justable | ||
| D.091 | DCF77 Status with connected external proble with DCF77 receiver | 0 = no reception 1 = reception 2 = synchronised 3 = valid |
Not ad- justable | ||
| D.092 | actoSTOR communication status | actoSTOR module detection 0 = Not connected 1 = Connection fault: No communication via PeBus, actoSTOR module was previously detected 2 = Connection active |
Not ad- justable | ||
| D.093 | Adjust Device Specific Number | Device Specific Number (DSN) Adjustment range: 0 to 99 | |||
| D.094 | Clear fault history | Delete fault list 0 = No 1 = Yes |
|||
| D.095 | Software version: PeBUS parti- cipant | PCB (BMU) Display (AI) actoSTOR (APC) HBI/VR34 | Not ad- justable | ||
| D.096 | Reset to factory settings? | Reset all adjustable parameters to factory setting 0 = No 1 = Yes |
|||
| D.097 | Activation of the second diagnostic level | Password:17 | Password:17 | ||
| D.098 | Coding resistor | Display xx.yy xx = Coding resistor 1 in cable harness for output range: 8 = VU 126/5-5 (H-GB) ecoTEC plus 612; VU 156/5-5 (H-GB) ecoTEC plus 615; VU 186/5-5 (H-GB) ecoTEC plus 618, VU 186/5-5 (P-GB) ecoTEC plus 618; VUW 196/5-5 (H-GB) ecoTEC plus 825 9 = VU 246/5-5 (H-GB) ecoTEC plus 624; VUW 246/5-5 (H-GB) ecoTEC plus 832; VUW 246/5-5 (P-GB) ecoTEC plus 832 10 = VU 306/5-5 (H-GB) ecoTEC plus 630; VU 306/5-5 (P-GB) ecoTEC plus 630; VUW 306/5-5 (H-GB) ecoTEC plus 835 11 = VU 386/5-5 (H-GB) ecoTEC plus 637; VUW 286/5- 5 (H-GB) ecoTEC plus 838; VUI 286/5-5 (H-GB) ecoTEC plus 938 yy = Coding resistor 2 on PCB for gas group: 02 = P gas 03 = H gas 07 = L gas |
Not ad- justable |
Smarter Heating & Hot Water